Search found 12 matches
- Feb 25th, 2021, 2:42 pm
- Forum: Frames, Hulls, & Bouyancy
- Topic: Penetrator for my ROV max. 100 Meter deep
- Replies: 4
- Views: 5796
Re: Penetrator for my ROV max. 100 Meter deep
The single core has a reason it is almost impossible to be sure that your epoxy gets in between all the wires of a multicore wire. While water pressure is a sure way to find any crack between the wires. You could use just a short piece of single core and solder a regular wire to it outside the pene...
- Feb 24th, 2021, 5:32 pm
- Forum: Frames, Hulls, & Bouyancy
- Topic: Penetrator for my ROV max. 100 Meter deep
- Replies: 4
- Views: 5796
Penetrator for my ROV max. 100 Meter deep
Hey, I'm thinking about to use the Blu Robotic Watertight Enclosure for ROV/AUV (4″ Series) https://bluerobotics.com/store/watertight-enclosures/4-series/wte4-asm-r1/ So, the first challenge will be to get a water tight connection from the BLDC-Motors inside the Hull. The Blue Robotics Penetrator ar...
- Feb 23rd, 2021, 4:18 pm
- Forum: Control Systems and Tethers
- Topic: Problems Arduino Nano V3 and MAX485 no clear connection
- Replies: 18
- Views: 15859
Re: Problems Arduino Nano V3 and MAX485 no clear connection
Thank you.
I'm almost done with my Rover Projekt.
The Full Duplex Communication working good. Only the Live View is a little bit noise.
I'm almost done with my Rover Projekt.
The Full Duplex Communication working good. Only the Live View is a little bit noise.
- Nov 26th, 2020, 11:33 am
- Forum: Control Systems and Tethers
- Topic: Analog Video Balun Problem
- Replies: 2
- Views: 4607
Re: Analog Video Balun Problem
All good, did two things wrong and I think one Balun was broken.PhilA wrote:Have you tried the set up with out the baluns in place?
Now it's working fine only the image quality is a little bit bad.
I see a lot of ants in the Screen.
- Nov 19th, 2020, 7:49 am
- Forum: Control Systems and Tethers
- Topic: Analog Video Balun Problem
- Replies: 2
- Views: 4607
Analog Video Balun Problem
Hello, at the moment I'm testing my ROVER. On the ROVER a RunCam Swift 2 is installed. The Cam working fine in FPV Mode by wireless transmitter. But now I installed the CAT5 Cable (75 m long) and on both ends a Video Balun. This one here from Banggood: https://www.banggood.com/de/2Pair-HD-720P1080P-...
- Jul 16th, 2020, 5:34 pm
- Forum: Control Systems and Tethers
- Topic: Problems Arduino Nano V3 and MAX485 no clear connection
- Replies: 18
- Views: 15859
Re: Problems Arduino Nano V3 and MAX485 no clear connection
asesorplaza1 wrote:Buenas tardes.
La respuesta es SI, debes unir las masas o GND de todo el circuito.
Un saludo.
Good afternoon.
The answer is YES, you must join the masses or GND of the entire circuit.
Greetings.
Good afternoon
Ok, Thank you
- Jul 16th, 2020, 3:00 pm
- Forum: Control Systems and Tethers
- Topic: Problems Arduino Nano V3 and MAX485 no clear connection
- Replies: 18
- Views: 15859
Re: Problems Arduino Nano V3 and MAX485 no clear connection
I have maybe stupid question. I using the MAX485 Bords and I power those boards and both arduinos with a seperate power source. So the only connection between the two systems is the wires A and B. Is it necessary to connect the GND together. GND from arduino Master to GND Arduino Slafe? http://www.t...
- Jul 12th, 2020, 3:26 pm
- Forum: Control Systems and Tethers
- Topic: Problems Arduino Nano V3 and MAX485 no clear connection
- Replies: 18
- Views: 15859
Re: Problems Arduino Nano V3 and MAX485 no clear connection
Hi! I use techmonkey based code modified for my own needs, easy transfer protocol, and RS485 boards that don't need control lines for the tx/rx switching. I had no end of problems with the cheap rs485 boards and went for slightly more expensive boards that detect when you TX and do the switching fo...
- Jul 8th, 2020, 6:20 pm
- Forum: Control Systems and Tethers
- Topic: Problems Arduino Nano V3 and MAX485 no clear connection
- Replies: 18
- Views: 15859
Re: Problems Arduino Nano V3 and MAX485 no clear connection
I also try this example out https://naylampmechatronics.com/blog/37_Comunicaci%C3%B3n-RS485-con-Arduino.html And it works fine. Servo is driving exactly the analog input of the master. I'm not sure what example I have to use for the thusters. I see here many examples. The http://www.techmonkeybusine...
- Jul 8th, 2020, 4:55 pm
- Forum: Control Systems and Tethers
- Topic: Problems Arduino Nano V3 and MAX485 no clear connection
- Replies: 18
- Views: 15859
Re: Problems Arduino Nano V3 and MAX485 no clear connection
Buenas tardes Aquí tienes algo que te puede ayudar bastante con la conexión de los módulos RS485, las paginas están escritas en Español, pero con el San Google Chrome las puedes traducir, un saludo. Good afternoon Here's something that can help you a lot with the connection of the RS485 modules, th...