Search found 11 matches
- Jul 20th, 2013, 5:05 pm
- Forum: Thrusters
- Topic: Brushless motor minimum speed ?
- Replies: 6
- Views: 4339
Re: Brushless motor minimum speed ?
Thanks for all reply ! Ok ,sensored can be a solution for hight efficient, and can be a solution . But I'couldnt think modify one esc soft or hard for a beginner like me . I read your post ,and effectualy after test a less Kv motor can be a solution ,but big motor ,need hight voltage for run ! i see...
- Jul 13th, 2013, 5:31 am
- Forum: Thrusters
- Topic: Brushless motor minimum speed ?
- Replies: 6
- Views: 4339
Brushless motor minimum speed ?
Hi everybodys I think will employe brushless motor on my futur rov But in my some system test before ,see couldn't run under a minimal speed rpm with any esc controler . Do it possible run from null to few rpm speed with a brushless motor like 0 to 60 rpm in my exemple ... Or does are minimum speed ...
- Jun 15th, 2013, 1:23 pm
- Forum: Electronics
- Topic: Acquiring multi input on OSD
- Replies: 0
- Views: 4094
Acquiring multi input on OSD
Hi everybodys ! Newbye in this system and very interest, I would like display multi analog input on my Videoscreen , and can custom it , like have pressure in bar ,temperature, current ,speed of three motor . I have no problem to convert their physical value on µcontroler card ,but don't know if can...
- May 11th, 2013, 4:19 pm
- Forum: Control Systems and Tethers
- Topic: Turnigy 9X and ppm to pwm converter
- Replies: 8
- Views: 5953
Re: Turnigy 9X and ppm to pwm converter
Here a very simplist sheme of the modification on the attached document ... Some people can say ,learning port work too in this configuration : Yes, allright ,but in power off configuration without the 2.4Ghz module ,and no backlight (if you have one like me ), and you can break the very thin coaxia...
- May 11th, 2013, 10:32 am
- Forum: Control Systems and Tethers
- Topic: Turnigy 9X and ppm to pwm converter
- Replies: 8
- Views: 5953
Re: Turnigy 9X and ppm to pwm converter
hi Slimsy, In first ,did no explain good ,what i'was do . I realized a direct connection from my Transmitter (turnigy ) to my own built receptor just like this circuit attached in my post , don't use any commercial receptor, cause internal bus not ppm . In your transmitter from the main board (where...
- May 4th, 2013, 5:46 pm
- Forum: Control Systems and Tethers
- Topic: Turnigy 9X and ppm to pwm converter
- Replies: 8
- Views: 5953
Re: Turnigy 9X and ppm to pwm converter
Hi Slimsy ! Think answer to this post long time after ,but listen ... I wanted control a little rov with my Turnigy 9x too ,and with a simple ic and few componant (no programing needed) You can control about 9 chanel trought a bifilar tether connected on your radio. Using trainer port work good ,but...
- Feb 3rd, 2013, 6:47 am
- Forum: Control Systems and Tethers
- Topic: Control ROV throught learning's emiting port
- Replies: 7
- Views: 3496
Re: Control ROV throught learning's emiting port
OUps !
Excuse me, (the alea of my translation error !)
If I think good ,you ask me if your card work ?
I do my prototype on fly wire ,and work good ,and i think yours too.
Excuse me, (the alea of my translation error !)
If I think good ,you ask me if your card work ?
I do my prototype on fly wire ,and work good ,and i think yours too.
- Feb 3rd, 2013, 6:37 am
- Forum: Control Systems and Tethers
- Topic: Control ROV throught learning's emiting port
- Replies: 7
- Views: 3496
Re: Control ROV throught learning's emiting port
Hi Fluxno ! Actually ,I built my card with my CAO soft . I built a pcb particular ,for some test , like : -acquiring in/out signal for my logic analyser with sub d port , -powering with a LT1084 (3A capability ) -external count for test It is few little modification ,not very important in the concep...
- Jan 31st, 2013, 5:31 pm
- Forum: Control Systems and Tethers
- Topic: Control ROV throught learning's emiting port
- Replies: 7
- Views: 3496
Re: Control ROV throught learning's emiting port
Thanks ! Fluxno ,actually can't test this modification ;
But in 2 day can, and change their value .
I just buyed my tether cable for send video and data like helmet audio speaker cable (two monoshielded wire #22)
This week I would build this decoder and would test it .
Thanks your help !
But in 2 day can, and change their value .
I just buyed my tether cable for send video and data like helmet audio speaker cable (two monoshielded wire #22)
This week I would build this decoder and would test it .
Thanks your help !
- Jan 12th, 2013, 9:04 am
- Forum: Control Systems and Tethers
- Topic: Control ROV throught learning's emiting port
- Replies: 7
- Views: 3496
Re: Control ROV throught learning's emiting port
Hi fluxno! Thanks for your reply ! I knows the precedent ppm to pwm converter using 4017 chip and tried to used it on my transmiter ,but dont work or work no good . Cause I think my transmitter use 9 channel ,but today I 'am trying to have an emitter / receptor based on this application gived on thi...